physical properties test method imperial values metric values @ 2.0 mil (1) ultimate tensile md astm d 882 3400 psi 23 n/mm 2 td 2600 psi 18 n/mm 2 ultimate elongation md astm d 882 610 % 610 % td 560 % 560 % t ensile modulus, 2% secant md astm d 882 49,000 psi 338 n/mm 2 td 67,000 psi 462 n/mm 2 elmendorf tear md astm d 1922 20 g/mil 1 g/m td 80 g/mil 3 g/m t echnical information xu 66129.00 developmental monolayer adhesive film *trademark of the dow chemical company. ?see ?andling considerations?reverse side. form no. 299-50172-0801 smg (1)values are averages of typical film; not to be construed as specifications. xu 66129.00 developmental monolayer adhesive film is a heat-activated, thermally stable adhesive film capable of bonding to urethane foam-backed fabrics, paper, fiberglass, nonwovens, and rigid urethanes. this thermally activated adhesive film can be pre-applied to foam-backed fabrics and reactivated to bond to sub- strates in molding operations. this film is a high flow adhesive that is useful for bonding substrates while opening up for breathability and adding stiffness to the final part. heat activation point: 266f (130c) y ield: 204 (sq ft/lb/mil) (41 m 2 /kg/25 m) a vailable colors: clear gauge range: 1.5-4.0 mil (37.5-102 m) width range: 20-75 in (508-1905 mm)
form no. 299-50172-0801 smg 9086 smg handling considerations material safety data sheets for integral adhesive films are available from the dow chemical company to help customers/ users further understand the proper han- dling of the product. a current msd sheet should be requested from your dow sales representative prior to working with the product. health & safety integral adhesive films products present no unusual health hazards when used in their intended manner. observe usual industrial safe handling practices. protect workers from possible contact with hot or molten film. assure workers of a fresh air supply by appropriate exhaust and ventilation of work areas, especially where film is located. avoid breathing dusts if such are generated. during manufacture, handling or use, most film webs will develop and retain a static electrical charge. the magnitude of the charge and how long it will be stored are dependent upon the composition of the web, the kind of handling, and the atmos- pheric conditions, particularly humidity. integral adhesive films can discharge such stored electrical energy in the form of a spark, and therefore should not be handled in a flammable or explosive environment. consult a current msd sheet prior to working with the product. combustion characteristics integral adhesive films is made of organic ethylene polymers and therefore will burn under the right conditions of heat and oxygen supply. when burning, the product may contribute high fuel value. normal precautions should be taken to avoid exposure to open flame and other ignition sources. fires can be extinguished with water, carbon dioxide, or other con- ventional means, with water fog preferred. in enclosed areas, firefighters should use a self-contained breathing apparatus. cgmp the films produced by the dow chemical company in north america are produced in facilities that follow the good manufacturing practices guide for bulk pharmaceutical excipient. this guide has been created by an international consortium to address the needs of excipients. this product may be produced and sold in europe, which does not require the adherence to the fda good manufacturing principles. please contact the business product stewardship specialist if more details are needed. product stewardship the dow chemical company has a fundamental concern for all who make, distribute, and use its products, and for the environment in which we live. this concern is the basis of our product stew- ardship philosophy by which dow assesses the health and environmental information on our products and then takes appropriate steps to protect employee and public health and the environment. the dow product stewardship program rests with every individual involved with dow products from initial concept and research to the manu- facture, sale, distribution, and disposal of each product. customer notice dow encourages its customers and potential users of dow products to review their applications for such products from the standpoint of human health and envi- ronmental quality. dow personnel will assist customers in dealing with ecological and product safety considerations. your dow sales representative can arrange the proper contacts. dow product literature, including material safety data sheets, should be consulted prior to the use of dow products. these may be obtained from your dow sales representative. disposal when burned in controlled industrial or municipal incinerators, these films will be consumed with very little resultant ash or smoke. the predominant products of combustion are carbon dioxide and water. if the incinerator is not designed to manage products having the high heat value of plastics, these films should be admixed (<10%) with low heat value waste so the combustion capacity of the incinerator is not exceeded. when disposed of in a sanitary land- fill, these films do not evolve gases or leachates known to pollute water resources. because they do not provide a food source for bacteria, fungi, insects, or rodents, the films do not attract vermin or vectors in landfill disposal. in any disposal of wastes, be certain all applicable federal, state, and local regula- tions are met. iso 9000 certification the engineered films and laminates business has well defined and documented quality systems at each site. the business has an established quality network with a business quality leader and plant quality coordinators to support maintenance of the quality systems. the quality systems at each site have been third party certified to the iso 9002 standard. we will be applying for certification to iso 9001:2000 in the near future. operation of disciplined quality systems is extremely important to us. this is how we assure we can produce and deliver quality products and services that our customers expect. packaging/labeling/traceability shipping container will be of sufficient strength and construction to ensure safe transportation to destination under normal shipping conditions. each roll and shipment will contain a lot number that is traceable through production records to input materials and process con- ditions. material traceability will be according to current good manufacturing practice (cgmp) guidelines in dow north american facilities. dow automotive ? , 1250 harmon rd., auburn hills, mi 48326 usa 1-800-441-4369 or 989-832-4569 dow customer information group, edegem, belgium +800 3 694 6367* or +32 3 450 2240 t elefax: +32 3 450 2815 *toll free from austria, belgium, denmark, finland, france, germany, hungary, ireland, italy, the netherlands, norway, portugal, spain, sweden, switzerland, and the united kingdom. notice: no freedom from any patent owned by dow or others is to be inferred. because use conditions and applicable laws may dif fer from one location to another and may change with time, customer is responsible for determining whether products and the information in t his document are appropriate for customer?s use and for ensuring that customer?s workplace and disposal practices are in compliance with applica ble laws and other governmental enactments. dow assumes no obligation or liability for the information in this document. no warranties are given; all implied warranties of merchantability or fitness for a particular purpose are expressly excluded. published august 2001 * t rademark of the dow chemical company. ? dow automotive, a business unit of the dow chemical company and its subsidiaries. printed in u.s.a.
|
